1 Ton Industrial Steam Boilers
Capacity:1-20t/h
Rated thermal efficiency: 100-104%
Fixed working pressure: ≤1.6MPa
Applicable fuel:natural gas etc.
Capacity:0.7-14MW
Rated thermal efficiency:96-98%
Fixed working pressure:≤1.25MPa
Applicable fuel:Natural gas, light oil, etc.
Capacity:0.7-2.8Mw
Rated thermal efficiency: 97.2-106%
Fixed working pressure:0.1MPa
Applicable fuel:Natural gas, etc.
Capacity:2.8-7.0Mw
Rated thermal efficiency:≥105.5%
Fixed working pressure:-0.02MPa
Applicable fuel:Natural gas, etc.
Capacity:99Kw
Rated thermal efficiency:97.2-104.4%
Fixed working pressure:1.0MPa
Applicable fuel:Natural gas, etc.
Capacity:0.5-4.0 t/h
Rated thermal efficiency:98%
Fixed working pressure:≤1.25MPa
Applicable fuel:electric energy
Nov 07, 2016 · Boilers are used to generate steam or hot water and can be fired by natural gas, fuel oil, or coal. The following boilers have combustion efficiencies between 78% and 86%. Small air-cooled electric chillers have 1.6-1.1 kW/ton …Get Price
Jan 01, 2013 · An economizer or APH for water-tube boilers is typically not attractive for units operating under 10 kg/cm 2 g or below 20 ton/h of steam production, nor any size boiler that will normally run at reduced capacity. For industrial boilers, dual installation using both an economizer and an APH is rarely economical or installed.Get Price
A pulverized coal-fired boiler is an industrial or utility boiler that generates thermal energy by burning pulverized coal (also known as powdered coal or coal dust since it is as fine as face powder in cosmetic makeup) that is blown into the firebox.. The basic idea of a firing system using pulverised fuel is to use the whole volume of the furnace for the combustion of solid fuels.Get Price
A pulverized coal-fired boiler is an industrial or utility boiler that generates thermal energy by burning pulverized coal (also known as powdered coal or coal dust since it is as fine as face powder in cosmetic makeup) that is blown into the firebox.. The basic idea of a firing system using pulverised fuel is to use the whole volume of the furnace for the combustion of solid fuels.Get Price
Nov 07, 2016 · Boilers are used to generate steam or hot water and can be fired by natural gas, fuel oil, or coal. The following boilers have combustion efficiencies between 78% and 86%. Small air-cooled electric chillers have 1.6-1.1 kW/ton …Get Price
Jan 01, 2013 · An economizer or APH for water-tube boilers is typically not attractive for units operating under 10 kg/cm 2 g or below 20 ton/h of steam production, nor any size boiler that will normally run at reduced capacity. For industrial boilers, dual installation using both an economizer and an APH is rarely economical or installed.Get Price
Nov 07, 2016 · Boilers are used to generate steam or hot water and can be fired by natural gas, fuel oil, or coal. The following boilers have combustion efficiencies between 78% and 86%. Small air-cooled electric chillers have 1.6-1.1 kW/ton …Get Price
Jan 01, 2013 · An economizer or APH for water-tube boilers is typically not attractive for units operating under 10 kg/cm 2 g or below 20 ton/h of steam production, nor any size boiler that will normally run at reduced capacity. For industrial boilers, dual installation using both an economizer and an APH is rarely economical or installed.Get Price
"The boilers and pipes were found to be terribly inefficient and resulted in a heat loss of 4,000,000 Btu's in the machine shop alone," Walker noted. "It wasn't a closed loop central heating system and consisted of steam being piped into insulated radiators and fans located above the floor in the three facilities.Get Price
"The boilers and pipes were found to be terribly inefficient and resulted in a heat loss of 4,000,000 Btu's in the machine shop alone," Walker noted. "It wasn't a closed loop central heating system and consisted of steam being piped into insulated radiators and fans located above the floor in the three facilities.Get Price
"The boilers and pipes were found to be terribly inefficient and resulted in a heat loss of 4,000,000 Btu's in the machine shop alone," Walker noted. "It wasn't a closed loop central heating system and consisted of steam being piped into insulated radiators and fans located above the floor in the three facilities.Get Price